Description
This Kit Fits:
2024-2025 Hyundai Santa Fe – this front only kit works on all trim levels
SE, SEL, XRT ( with factory lift), Limited and Calligraphy
It will fit all of the 2024-2025 Hyundai Santa Fe’s….
Yes, that’s right…this kit fits that shiny new 2024 Hyundai Santa Fe sitting in your driveway….you know, the one when you look out your window into the driveway or on the street and looks almost perfect but something is just off…you keep looking and it hits you…your beutiful new Santa Fe sits WAAAAAY TO LOW in the front….ugh….
Worry not, we have the solution, our 1.25″ front only lift kit will fix all those problems ( and let you fit those snow tires the dealer promised to throw in when the snow starts!)
This #305034 is for the FWD or AWD versions, any trim level, it’s purpose is to makes the Santa Fe sit close to level, but it is your vehicle, feel free to make it your own with one of our other kits that also lifts the rear!
Like all of our parts, this kit is designed to work WITH the stock parts that came on your vehicle, no need to modify any parts, we include everything you need to create the do anything Santa Fe….
We have been doing this for a long time (we built our first unibody lift in 2005) and while we would LOVE to make it an even taller kit, we tried that already ~ our original design was a 2.5″ kit and it was just a little too much – we didn’t like the angles and how it drove, while some people would be fine with it, we design every part we make to keep your vehicle driving and operating like stock; and do our best to make sure parts do not wear out any faster than they would without our kit installed.
This kit will increase your front ground clearance and keep that air dam and bumper out of the mud or sand on those trips to the cabin or the beach, and yes, when you add a size or two *taller* tire you will get 2.0 -3.0″ MORE ground clearance.
This kit has been tested with full throttle, wheels sliding and basically…well doing things you should never do to a new vehicle…we DO NOT recommend beating on your vehicle, you will break parts :-}
This is a straightforward install, yes we do include some very important simple install tricks in the instructions – you just need to make sure to read the instructions, they are not campfire starter!
There is NO cutting or welding or permanent modifications needed.
This lift kit allows you to fit much more aggressive tires and wheels allowing your Santa Fe/Sorento to take the family and all your toys to where they need to go!
***If you are not sure if you want to do just the front or add the rear, there is an easy trick….simply slide your floor jack under the front or the rear or both and jack it up 1.0 or 1.25 or 1.5″ – so if you find you do want more rear height, there is a good possibility we have a solution for you! feel free to call us @ 855.668.0541….don’t forget, all of our parts are made in house by us, not imported from offshore or made at Uncle Binky’s Welding Saloon in Guatemala ( nothing wrong with Guatemala, or Uncle Binky…just saying, we make all of our parts) so yes, the fact we make all of our parts means we make all of our parts means we actually test fit them and in most cases can answer your questions :-}
ALWAYS test fit wheels and tires AFTER lift install***
We have fit up to 265/60R18 tires on aftermarket wheels….make sure to send us pics so we can post them up and let people know what your choice was!
A GENERIC no vehicle specific Note about tire sizes: Every wheel and tire company seems to use a different measuring tape, one companies 265/60R18 will be 30.5 inches tall and another may be 31.5″ tall yet they have the same size on the sidewall – we can’t possibly test ALL combinations of wheels and tires so please install the kit before ordering tires or use an exact combination you have seen fit before!
All of our kits are a direct bolt in and require no modifications to your vehicle. These kits retain the stock ride quality of your truck as we use as many OEM parts as possible – keeping your truck under warranty is important, which is why we designed each kit to work with Factory parts..
Every Truxxx lift kit is made in the using USA or Canadian Mill Certified Steel and laser cut to precision tolerances using OEM drawings.
Every kit is welded using the latest US Made welders and triple checked to ensure proper fitment.
Each kit contains front strut spacers and sway bar extensions – we include all the all the required hardware in 10.9 & 12.9 grade, we have detailed instructions and complete alignment specs.
Recommended installation time is approx. 3 hours + alignment
Reviews
There are no reviews yet.