Description
This Kit Fits:
2024-2025 Kia Seltos 2wd & 4×4 – all models except EV
2024-2025 Hyundai Kona 2wd & 4×4 – all models except EV
So you just bought a Kia Seltos/Hyundai Kona, you have it loaded up and your ready to hit the road, head to that killer campground down at the lake or maybe you are heading to some amazing place up in the mountains, all the gear is loaded, your roof tent is on, the cooler has a weekends worth of refreshments and “let the adventure begin” mentality is wide open, all is great until you leave the pavement….quickly, your realize your killer new AWD SUV sits WAAAAAY TO LOW in the front, way to low in the rear and your underbelly starts dragging….even worse, when you load your mountain bike or snowboards on your hitch mount rack the back end of the SUV sags….guess what, we have a solution, our 2.0″ front and 2.0″ rear lift kit will help lead the way to fix all those problems!
This kit is the one we created for the person who wants (or needs) the benefits of a small car but still refuses to give up living the life of adventures…or someone who wanted to be ready for the adventure when opportunity arises!
This kit will allow you to create the perfect daily driver combination for the person who drives the vehicle daily to work and run errands, then hits the backroads on the weekends!
***The 304026 kit has been designed specifically for the adventurous Seltos and the Kona ~ this kit does not include the rear shock shaft extension, you can order part #304004 separately if you do decide you want it, or order part #304027 that does include the rear shock shaft extension.***
We have been selling this kit to Kia & Hyundai dealers around the world since it was released, this kit is designed to work WITH the stock parts that came on your vehicle, no need to modify any parts, we include everything you need to create the do anything Seltos/Kona….
We have been doing this for a long time (we built our first unibody lift in 2005) and while we would LOVE to make it an even taller kit, we tried that already ~ our original design for the Seltos/Kona was a 2.5″ kit and it was just a little too much – we didn’t like the angles and how it drove, while some people would be fine with it, we design every part we make to keep your vehicle driving and operating like stock; and do our best to make sure parts do not wear out any faster than they would without our kit installed.
This kit will increase your front ground clearance and keep that air dam and bumper out of the mud or sand on those trips to the cabin or the beach, and yes, when you add a size or two *taller* tire you will get 2.0 -3.0″ MORE ground clearance.
This kit has been tested with full throttle, wheels sliding and basically…well doing things you should never do to a new vehicle…we DO NOT recommend beating on your vehicle, you will break parts :-}
This is a straightforward install, yes we do include some very important simple install tricks in the instructions – you just need to make sure to read the instructions, they are not campfire starter!
There is NO cutting or welding or permanent modifications needed.
This lift kit allows you to fit much more aggressive tires and wheels allowing your Seltos/Kona to take the family and all your toys to where they need to go!
***ALWAYS test fit wheels and tires AFTER lift install***
We have fit up to 215/65R16 or 215/70R16 tires on aftermarket wheels….make sure to send us pics so we can post them up and let people know what your choice was!
A GENERIC no vehicle specific Note about tire sizes: Every wheel and tire company seems to use a different measuring tape, one companies 265/60R18 will be 30.5 inches tall and another may be 31.5″ tall yet they have the same size on the sidewall – we can’t possibly test ALL combinations of wheels and tires so please install the kit before ordering tires or use an exact combination you have seen fit before!
All of our kits are a direct bolt in and require no modifications to your vehicle. These kits retain the stock ride quality of your truck as we use as many OEM parts as possible – keeping your truck under warranty is important, which is why we designed each kit to work with Factory parts..
Every Truxxx lift kit is made in the using USA or Canadian Mill Certified Steel and laser cut to precision tolerances using OEM drawings.
Every kit is welded using the latest US Made welders and triple checked to ensure proper fitment.
Each kit contains front strut spacers and sway bar extensions – we include all the all the required hardware in 8.8 & 10.9 grade, we have detailed instructions and complete alignment specs.
Recommended installation time is approx. 3 hours + alignment and 27” tall tires are commonly used with a stock style offset wheel.
Reviews
There are no reviews yet.